Differences

This shows you the differences between two versions of the page.

--- bachin_d8-cnc2418 [2018/09/28 16:43]
ljx
+++ bachin_d8-cnc2418 [2019/01/28 11:38] (current)
ljx
@@ Line 3: / Line 3: @@
 **0.Overview**
-Shipment of parts, need to assemble the machine by yourself. Please watch the** [[assembly video]]** and **instruction manual** before starting assembly.
+Shipment of parts, need to assemble the machine by yourself. Please watch the [[assembly video]] and **instruction manual** before starting assembly.
 {{:img_3354详.jpg?600|}}{{:img_3355详.jpg?600|}}
@@ Line 31: / Line 31: @@
 {{:p3.png?600|}}
-**3.Run the software -- Candle**
+**3. Software connected**
 Candle is a portable software that does not need to be installed.
 Double click the Candle.exe to start.
-If you are using the MAC system, click Candle.dmg instead.
+If you are using the MAC system, click Candle.dmg instead. Learn more about [[candle|Candle]]
 {{:p4.png?600|}}
@@ Line 56: / Line 56: @@
 In this case, please try install the driver again, otherwise, please contact us and attach a circuit board photo and device manager screenshot.
+**4. Run the software -- Candle** Watch the video firstly: https://www.youtube.com/watch?v=IObj8f6JOCM
+Zero the Work Coordinates.
+{{:p8.png?600|}}
+We usually Zero the Work Coordinates after Moving a Axis .
+{{:p9.png?400|}}
+**Homing**{{:p10.png?100|}}
+Homing make machine go to the same start position for a Repeated Engraving. Only when a machine come with a XY limit switch, homing is available.
+Click the homing button, the engraving machine will move XY axes until reach the limit switch.
+After a homing, X&Y coordinates is set to (0,0).
+{{:w.jpg?100|}}Warning: please stay away from the engraving machine when the machine is homing.
+**5. Z Axis Probing**
+We must adjust the Z Axis height value before engraving. The simple way is move z axis, let the engraving knife just above the engraving level, then Zero the Z Coordinate. The quick way is using a Probe tool.
+Install Probe tool.
+Refer to the board connection picture for more information.
+{{:p11.png?600|}}
+Click the Probe Button>>{{:p12.png?100|}}
+The Z Axis will go down, reach the Probe Tool surface, stop, go up, stop finally. The Z axis height value will be adjust right when stop finally. Remove the Probe Tool.
+**Tip:** Do not Zero Z Coordinate after finished a Probing operation.
+**Unlock**>> {{:p13.png?100|}}
+The machine will go into Alarm State if something wrong happened. For example, the machine reach the limit switch when working.
+Exclude errors, click Unlock button to continue.
+**6. Start Engraving**
+Usually the engraving process is as bellow.
+Make a G-Code file  >> Power the Machine >> Run Candle  >> Load the G-Code File>>Place the Engraving Object >> Move to start point and Zero X&Y Coordinates >> Probe >> Start Engraving.
+We provide some examples to help you quickly familiarize yourself with the machine.
+Click Open, select a G-Code file in the Example G-Code file folder.
+{{:p14.png?600|}}
+After G-Code is loaded.  According to the above description Place the engraving object,  move to start point and zero X&Y Coordinates,  probe , finally click Send button to start engraving.
+{{:p15.png?600|}}
+**Pause & Stop Control**
+Click// Pause// to pause, Click Pause again to Continue. Click// Abort// to Stop.
+{{:p16.png?600|}}