Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
bachin_d8-4050p [2018/09/27 10:30] ljx |
bachin_d8-4050p [2021/02/23 09:50] ljx |
||
---|---|---|---|
Line 15: | Line 15: | ||
{{youtube>jzn5mif5Ldo?medium}} | {{youtube>jzn5mif5Ldo?medium}} | ||
- | 3. **Installing Engraver Master:**you can find the setup.exe from the USB flash driver or download from the wiki. | + | **3.Connected all the cables--**follow the picture: |
+ | |||
+ | |||
+ | {{:img_3233.png?600|}} | ||
+ | |||
+ | **4.** **Installing Engraver Master:**you can find the setup.exe from the USB flash driver or download from the wiki. | ||
After download the driver :**setup.exe** ,run this file then here comes an icon on the computer desktop . | After download the driver :**setup.exe** ,run this file then here comes an icon on the computer desktop . | ||
Line 23: | Line 28: | ||
the interface: | the interface: | ||
- | {{:001.png?400|}} | + | |
+ | {{:001.png?600|}} | ||
+ | |||
+ | **5.Engraver Master anatomy:** | ||
+ | |||
+ | See the top menu of the interface ,there have :Print Picture,NC Sender,Quick Tagging and Device Settings. | ||
+ | |||
+ | //**Print Picture--**// Suitable for gray style , and it's very slowly , so if you really need to engraving a gray style picture,we suggest you'e better use another software which more faster then this one .Here>>http://www.bachinmaker.com/update/laserprint/setup.exe | ||
+ | |||
+ | //**NC Sender**//--Automatically generate path files without trans-coding, fast speed and good effect.Recommended!Prefer this engraving mode. | ||
+ | {{:02副本.jpg?600|}} | ||
+ | |||
+ | |||
+ | //**Quick Tagging**//-here is for engraving the single line font . | ||
+ | |||
+ | //**Device Settings**//--setting the speed,laser powder ,machine type and so on. | ||
+ | Don't forget click on Save Settings when change any settings. | ||
+ | {{:002.png?600|}} | ||
+ | |||
+ | Now , it is ready to start the first engraving . | ||
+ | Please pay attention to protect your eyes and use protective glasses. | ||
+ | |||
+ | You should cut of the power when not use the machine . | ||
+ | |||
+ | Sometimes ,the software maybe disconnected ,don't worry ,Turn off and restart,or delete it and reinstalling again. | ||
+ | |||
+ | Can not use benbox software. | ||
+ | Supported the system:windows XP ,windows 7/8/10. Can not supported MAC. | ||
+ | |||
+ | **6.if you feel that the feet of the machine are not level, you can put a sponge paper or other thin object on the foot of the machine. | ||
+ | ** | ||
+ | see the follow picture: | ||
+ | |||
+ | {{:img_3495.jpg?600|}} | ||
+ | |||
+ | Links: | ||
+ | |||
+ | * [[carve_photos_at_fastest_speed|Carve photos at fastest speed]] | ||
+ | * [[solve_laser_problems|How to solve the Laser Problems]] | ||
+ | * [[solve_motor_problem|How to solve the Motor Problems]] | ||
+ | * [[d8_4050_1720_laser_assembly_problem|D8-4050P Assembly problems]] | ||
+ | * [[software_interface_problem|Windows7 Display Problem]] | ||
+ | * [[install_end_stop_switch_laser_machine|Install End Stop Switch for Laser Machine]] | ||
+ | * [[buy_new_belts|Buy new belts]] | ||
+ | * [[avoid_white_lines|How to avoid white lines]] | ||
+ | * [[update_firmware|How to Update Firmware on Board]] | ||
+ | * User [[light_burn|Light Burn]] application. | ||
+ | * [[4050_stop_half_the_project|4050 Laser stop half the project]] | ||