Differences
This shows you the differences between two versions of the page.
Next revision | Previous revision | ||
create_nc_file [2019/05/06 17:20] ljx created |
create_nc_file [2019/05/07 12:37] (current) ljx inkscape |
||
---|---|---|---|
Line 6: | Line 6: | ||
Installation :http://bachinmaker.com/wiki/doku.php?id=inkscape | Installation :http://bachinmaker.com/wiki/doku.php?id=inkscape | ||
+ | |||
+ | ====== PART 1--Text G-code====== | ||
+ | |||
Step 1.Create Text G-code(NC file) | Step 1.Create Text G-code(NC file) | ||
Line 11: | Line 14: | ||
New folder name :output {{:i0.png?150|}} | New folder name :output {{:i0.png?150|}} | ||
- | Step 2.New document and set the properties | + | Step 2.New document and set the properties: |
+ | |||
+ | Inkscape >> Document properties >> Set the size 100 mm | ||
+ | |||
+ | {{:i3.png?600|}} | ||
+ | |||
+ | Step 3. Input text | ||
+ | |||
+ | {{:i4.png?600|}} | ||
+ | |||
+ | {{:i5.png?600|}} | ||
+ | |||
+ | Step 4. Path >> object to path: | ||
+ | |||
+ | {{:i6.png?600|}} | ||
+ | |||
+ | Step 5. Extensions >> Bachinmaker TOOL >> Gcode output | ||
+ | |||
+ | {{:i7.png?600|}} | ||
+ | |||
+ | {{:i8.png?600|}} | ||
+ | |||
+ | DONE!!{{:i9.png?200|}} | ||
+ | |||
+ | Load to the Engraver Master: | ||
+ | |||
+ | {{:i11.png?600|}} | ||
+ | |||
+ | **TIPS:** | ||
+ | If the NC file is imported into the engraving software, the engraving does not come out. | ||
+ | |||
+ | It may be due to the parameter setting problem. You need to adjust the relevant parameters. | ||
+ | |||
+ | Laser power set 600-1000 | ||
+ | |||
+ | Engraving/Draw Speed set 900-1500 | ||
+ | |||
+ | {{:i10.jpg?600|}} | ||
+ | |||
+ | ===== let's continue ===== | ||
+ | |||
+ | Starting from **step 4.** above | ||
+ | |||
+ | Extensions >> Bachinmaker TOOL >> Filling Gcode | ||
+ | |||
+ | {{:i12.png?600|}} | ||
+ | |||
+ | Then, Extensions >> Bachinmaker TOOL >> Gcode output (Same as step 5 above) | ||
+ | |||
+ | {{:i9-1.png?200|}} | ||
+ | Load to Engraver Master: | ||
+ | |||
+ | {{:i13.png?600|}} | ||
+ | |||
+ | ====== PART 2-Picture G-code ====== | ||
+ | |||
+ | Step 1. Import jpg ,jpeg, bmp file: | ||
+ | |||
+ | {{:i14.png?600|}} | ||
+ | |||
+ | {{:i15.png?600|}} | ||
+ | |||
+ | {{:i16.png?600|}} | ||
+ | |||
+ | Step 2. Path >> Trace Bitmap >> OK | ||
+ | |||
+ | {{:i18.png?600|}} | ||
+ | |||
+ | Step 3. Delete the original picture,keep the new one | ||
+ | |||
+ | {{:i19.png?600|}} | ||
+ | |||
+ | {{:i20.png?600|}} | ||
+ | |||
+ | Step 4.Extensions >> Bachinmaker TOOL >> Gcode output | ||
+ | |||
+ | {{:i21png.png?600|}} | ||
+ | |||
+ | Load to Engraver Master : | ||
+ | |||
+ | {{:i22png.png?600|}} | ||
+ | |||
+ | Step 5. Filling picture : | ||
+ | |||
+ | {{:i23png.png?600|}} | ||
+ | |||
+ | Then Gcode output(Same as step 4.) | ||
+ | |||
+ | Load to Engraver Master : | ||
+ | |||
+ | {{:i24png.png?600|}} | ||
+ | |||
+ | About Engraver Master : | ||
+ | |||
+ | http://bachinmaker.com/wiki/doku.php?id=engraver_master | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||