Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
bachin_d8-4050p [2018/09/27 11:40] ljx |
bachin_d8-4050p [2021/02/23 09:50] (current) ljx |
||
|---|---|---|---|
| Line 16: | Line 16: | ||
| **3.Connected all the cables--**follow the picture: | **3.Connected all the cables--**follow the picture: | ||
| + | |||
| {{:img_3233.png?600|}} | {{:img_3233.png?600|}} | ||
| Line 26: | Line 27: | ||
| the interface: | the interface: | ||
| + | |||
| {{:001.png?600|}} | {{:001.png?600|}} | ||
| Line 35: | Line 37: | ||
| //**Print Picture--**// Suitable for gray style , and it's very slowly , so if you really need to engraving a gray style picture,we suggest you'e better use another software which more faster then this one .Here>>http://www.bachinmaker.com/update/laserprint/setup.exe | //**Print Picture--**// Suitable for gray style , and it's very slowly , so if you really need to engraving a gray style picture,we suggest you'e better use another software which more faster then this one .Here>>http://www.bachinmaker.com/update/laserprint/setup.exe | ||
| - | //**NC Sender**//--Automatically generate path files without trans-coding, fast speed and good effect.Recommended！ | + | //**NC Sender**//--Automatically generate path files without trans-coding, fast speed and good effect.Recommended！Prefer this engraving mode. |
| {{:02副本.jpg?600|}} | {{:02副本.jpg?600|}} | ||
| + | |||
| //**Quick Tagging**//-here is for engraving the single line font . | //**Quick Tagging**//-here is for engraving the single line font . | ||
| Line 46: | Line 49: | ||
| Now , it is ready to start the first engraving . | Now , it is ready to start the first engraving . | ||
| Please pay attention to protect your eyes and use protective glasses. | Please pay attention to protect your eyes and use protective glasses. | ||
| - | you should cut of the power when not use the machine . | + | |
| + | You should cut of the power when not use the machine . | ||
| Sometimes ,the software maybe disconnected ,don't worry ,Turn off and restart,or delete it and reinstalling again. | Sometimes ,the software maybe disconnected ,don't worry ,Turn off and restart,or delete it and reinstalling again. | ||
| + | |||
| + | Can not use benbox software. | ||
| + | Supported the system:windows XP ,windows 7/8/10. Can not supported MAC. | ||
| + | |||
| + | **6.if you feel that the feet of the machine are not level, you can put a sponge paper or other thin object on the foot of the machine. | ||
| + | ** | ||
| + | see the follow picture: | ||
| + | |||
| + | {{:img_3495.jpg?600|}} | ||
| + | |||
| + | Links: | ||
| + | |||
| + | * [[carve_photos_at_fastest_speed|Carve photos at fastest speed]] | ||
| + | * [[solve_laser_problems|How to solve the Laser Problems]] | ||
| + | * [[solve_motor_problem|How to solve the Motor Problems]] | ||
| + | * [[d8_4050_1720_laser_assembly_problem|D8-4050P Assembly problems]] | ||
| + | * [[software_interface_problem|Windows7 Display Problem]] | ||
| + | * [[install_end_stop_switch_laser_machine|Install End Stop Switch for Laser Machine]] | ||
| + | * [[buy_new_belts|Buy new belts]] | ||
| + | * [[avoid_white_lines|How to avoid white lines]] | ||
| + | * [[update_firmware|How to Update Firmware on Board]] | ||
| + | * User [[light_burn|Light Burn]] application. | ||
| + | * [[4050_stop_half_the_project|4050 Laser stop half the project]] | ||
| + | |||